中文乱码人妻一区二区三区在线-国产亚洲美女精品一区-欧美性情大片一区二区-中文有码在线观看免费

產品|公司|采購|招標

環保APP正式上線

200噸立式液壓打包機

參考價面議
具體成交價以合同協議為準
  • 公司名稱東莞市大田塑膠機械廠
  • 品       牌
  • 型       號
  • 所  在  地
  • 廠商性質經銷商
  • 更新時間2024/10/24 13:07:37
  • 訪問次數121
產品標簽:

在線詢價收藏產品 點擊查看電話

大田公司是注塑成型周邊機械*生產廠家。隨著人們對塑膠產品的要求越來越高,注塑工藝日益*。因此,公司不僅注重產品品質,更致力于研究開發高效、節能、環保之優質產品、以感謝廣大新老客戶的支持與厚愛?! {借十多年的技術革新優勢和工程技術人員的不斷探索,為產品的更新?lián)Q代,精益求精,奠定了堅實的基礎。在所有產品的設計和制造上都體現了客戶的寶貴意見及市場的適用性,力求盡善盡美;在主要部件方面,全部采用日本、美國、法國等進口壓縮機組;意大利、中國臺灣、韓國、日本等電機、電器、泵浦,從而確保產品的性能和品質,使公司順利獲得了德國來茵公司ISO-9002品質認證,產品廣泛用于塑膠、電子、電鍍、化學、五金、食品等行業。選用大田機械必將給您帶來更大的效益回報?! ≌雇磥?,我們充滿信心,憑自身完善的售后服務及性能*的產品,我們希望能與各行業攜手共進,共創美好的明天。

吸料機;上料機;抽料機;送料機;模溫機;冷水機;干燥機;碎料機;冷水塔;液壓打包機;攪拌機;脫水機;干衣機;洗衣機
200噸立式液壓打包機 2200噸立式液壓打包機廢料打包機, 配用動力:18.5KW,臺時產量:3-5個包塊,包重:500-1500KG,油缸:Φ160*2支,操作方便, 接上電源后打包 , 專用于一切輕泡、松散物料的打包??蓱?yīng)用于用于有色金屬板材及型材和輕簿型塑料
200噸立式液壓打包機 產品信息


2200噸立式液壓打包機廢料打包機, 配用動力:18.5KW,臺時產量:3-5個包塊,包重:500-1500KG,油缸:Φ160*2支,操作方便, 接上電源后打包 , 專用于一切輕泡、松散物料的打包??蓱?yīng)用于用于有色金屬板材及型材和輕簿型塑料,棉、羊毛、廢紙、廢紙箱、廢紙板、紗線、塑料、布匹、編織袋、針織絨、麻、麻袋、毛條、毛球、繭、蠶絲、啤酒花、麥柴、草、廢塑料袋等一切輕泡、松散物料。包型緊湊,整齊美觀,可大幅降低運輸成本,是棉產區、紡織企業、超市、服裝廠、廢舊物資回收業和其他各種輕工業企業的生產工具 。200噸雙缸液壓打包機,

200噸立式液壓打包機型號:200公稱壓力主缸KN:2000液體*大工作壓力MPa:18料箱尺寸長1500mm,寬700mm,高:1400mm包塊尺寸:長1100mm*寬:700 *高:(1000)mm包塊密度kg/m3:≥1300單次循環時間S:55電機功率KW:18.5油缸行程:1200MM機器外形尺寸mm:長2600*寬2400*高4100。整機重量kg;7300.

200噸立式液壓打包機使用說明:本廠液壓打包屯機使用68#液壓油,連接電源三相380V,額定電流為40A,安裝時要有接地保護,電機要根據所示方向運轉才能啟用,否則不能啟動。油箱加入液壓油方可啟動使用。但當氣溫降低時液壓油濃度大,機內的濾清器不能起到過濾作用,這時必須將濾清器拆出,待溫度恢復后,方可生新安裝使用。(注:濾清器應每月清洗1-2次)。 溢流筏-控制該機的壓力開關,旋轉調壓手轉向右轉為增壓,向左轉為減壓,出廠前已調整好壓力。但在使用過程中調壓手輪可能有變位現象,導致壓力升高或降低,這時需要生新調節壓力,調壓時應在運轉中進行,同時把壓板降至* 低位置,調整溢流筏的調壓手輪,調整壓力不能高于或低于壓力表所示的范圍,壓力的OMPA(100KG/1cm2)。旁桿-增強壓的剛性和起導向作用,每次使用前應加油,起潤滑作用。 行程開關-控制該機的啟動和停止的作用,因此要經常檢查、維修、保養。手動轉向閥-控制壓板向上向下,停止的開關。 1、手動轉向閥打向下檔位時壓板自動向下工作,當廢紙壓到結實狀態時,那阻力大于壓力:壓板不能再向下壓,應把手動轉向閥打向空檔位置,停止加壓,如果長期處于加壓狀態,會導致液壓,電機、油泵長時間處于超負荷狀態而使各機件損壞。 2、手動轉向閥打向升檔位置,壓板自動向上升到*高的位置,由行程開關控制自停,這時應把手動轉向空檔位置。完成一個工作程序。

200噸立式液壓打包機使用說明書:一、安裝步驟1、本機必須平穩放在混凝土上,基礎視當?shù)厍闆r決定。2、檢查油箱底部放油口是否已關閉,確定關閉后再打開油箱頂部加油口密封蓋。注入約90KG,68#液壓油,液壓油排號視當?shù)貧鉁丶笆褂脴?biāo)準決定。[注!如果機型在60T以上,新機時必須分兩次注油,**次注入液壓油高度至油尺頂部(藍**線)。待壓板下壓至底部再加注液壓油至油尺底部(紅**線)詳細見操作說明4]3、安裝好本機電源線,電壓及頻率視當?shù)仉娫礇Q定,(注!電機和電器配件的電壓及頻率已按客戶訂購機器時的要求配置安裝好)常規采用三相四線制,其中三條帶電源線分別接入電相內相應的三個接線位,(圖7左)另一條為接地防漏電保護線,應緊接機體外露金屬表面,以防電器漏電傷人。

200噸立式液壓打包機操作方法:1、通入電源:把電箱內空氣開關(本機總開關)合上,先檢查三相電源電壓是否正常,(用儀表或探電筆測試)關閉電相門,查看電相門板表面紅色電源指示燈是否亮起。2、啟動電機:把手動換向閥手柄(付圖3)往下推至*底位(機體附有操作圖標),然后把啟動按鈕NO按下(圖5右下),(注:如裝有急停開關機型的請把急停開關按箭頭方向右旋,急停開關彈出即可),(圖5右上)如正常情況下電機啟動。3、 檢看電機轉向:(圖8)電機啟動后,手動換向閥手柄在*下位時,如壓板不能往下移。這時請必須立即查看電機旋轉方向是否正確,電機旋轉方向必須按箭頭指示方向一致。如果電機轉向相反時則機器不能正常使用,這時應把手動換向閥手柄往上拉至中檔位。然后按下停止按鈕OFF(或急停開關按下)停止電機運轉。切斷輸入總電源,把三相電源線其中二相線互換再接上即可。再按操作1和2重新操作,(注!必須確定電機轉向是否與箭頭指示方向一致。)4、注入油量的關?。寒?dāng)壓板正常往下移時,壓板在**次移動,移動速度是不均勻的。待壓板移至底部或移動中突然停止又或移動中噪聲加大,這種情況下應先把手動換向閥手柄往上拉至中位,把停止開關OFF或急停開關按下,停止電機運行。再仔細查看油箱儲油量是否足夠,如油量底于油箱高度一半時,證明油量不足,這時應再次往油箱注入適當液壓油。這次加油量應加至油位尺*底界線(紅**線)即可。200 tons of vertical hydraulic balerScrap balers, Equipped with power: 18.5KW,Taiwan when the output: 3-5 mass,Package weight: 500-1500KG,Cylinder: Φ160 * 2,Easy to operate, Connected to the power after packaging, dedicated to all light foam, loose material packaging. Can be used for non-ferrous metal sheet and profiles and light-type plastic materials such as cotton, wool, waste paper, waste paper boxes, waste paperboard, yarn, plastic, cloth, woven bags, knitted cashmere, linen, sacks, , Hair ball, cocoon, silk, hops, wheat chai, grass, waste plastic bags and so on all loose foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.200 tons of double cylinder hydraulic balerModel: 200Nominal pressure master cylinder KN: 2000Liquid maximum working pressure MPa: 18Box length 1500mm, width 700mm, height: 1400mmBulk size: Length 1100mm * Width: 700 * Height: (1000) mmBulk density kg / m3: ≥1300Single cycle time S: 55Motor power KW: 18.5Cylinder travel: 1200MMMachine dimensions mm: length 2600 * width 2400 * high 4100.Machine weight kg; 7300.Instructions for use:The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 40A, the installation should be ground protection, the motor should be operated according to the direction shown to be activated, or can not start. Fuel tank can be used to start the use of hydraulic oil. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month). Overflow raft - control the machine's pressure switch, rotary pressure hand turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication. Stroke switch - to control the machine's start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch. 1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts. 2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.Hydraulic baler instructions:First, the installation steps1, the machine must be placed on the concrete, the basic depending on the local situation.2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.Second, the operation method:1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.



15700106413
產品對比
QQ

咨詢中心

在線客服QQ交談

市場部QQ交談

發布詢價建議反饋
回到頂部

Copyright hbzhan.comAll Rights Reserved

環保在線 - 環保行業“互聯網+”服務平臺

對比欄

提示

×

*您想獲取產品的資料:

以上可多選,勾選其他,可自行輸入要求

個人信息:

日韩中文字幕免费在线视频| 极品熟女一区二区三区| 成人国产激情福利久久| 国产精品人妻熟女毛片av久久| 亚洲精品成人综合色在线| 亚洲欧洲日韩综合二区| 亚洲精品高清国产一线久久| 欧美一级不卡视频在线观看| 中文字幕亚洲精品人妻| 日韩性生活片免费观看| 日本精品中文字幕在线视频| 欧美亚洲综合另类色妞| 在线日韩中文字幕一区| 日韩精品成区中文字幕| 国产亚洲欧美日韩精品一区| 99福利一区二区视频| 高清一区二区三区不卡免费| 国产一区一一一区麻豆| 美女被啪的视频在线观看| 免费在线观看激情小视频| 久久精品国产亚洲av麻豆| 儿媳妇的诱惑中文字幕| 丰满人妻熟妇乱又伦精另类视频| 99热在线播放免费观看| 成人国产一区二区三区精品麻豆| 免费大片黄在线观看国语| 国产又粗又深又猛又爽又黄| 五月婷婷缴情七月丁香| 欧美在线观看视频免费不卡| 五月婷婷缴情七月丁香| 日本在线不卡高清欧美| 熟妇久久人妻中文字幕| 成人你懂的在线免费视频| 国产伦精品一一区二区三区高清版| 微拍一区二区三区福利| 国内九一激情白浆发布| 日本精品啪啪一区二区三区| 少妇人妻一级片一区二区三区 | 手机在线不卡国产视频| 91超频在线视频中文字幕| 99热在线精品视频观看|