3500/93系統顯示器旨在滿足美國石油協會(API)標準670的要求，并提供位于機架中的所有3500機械保護系統信息的本地或遠程視覺指示，包括:
·系統事件列表
·告警事件列表
所有通道，監視器，繼電器模塊，鍵相量*模塊或轉速表模塊數據
3500/93系統顯示通過3500機架配置軟件進行配置。顯示器可以以四種方式安裝:
1. 面部安裝-顯示器安裝直接在任何全尺寸3500機架使用特殊鉸鏈支持的前面板。這允許訪問機架的緩沖輸出連接器和用戶界面按鈕和開關，而無需斷開連接或禁用顯示。
注意:僅當采用此安裝方式時，DIM (Display Interface Module)必須安裝在機柜最右邊的15號槽位。面部安裝選項與3500迷你機架不兼容。
2. 19英寸EIA機架安裝-顯示器安裝在19英寸EIA導軌上，距離3500系統高達100英尺。(當使用外部電源時，距離3500系統最多4000英尺)。
3. 面板安裝-顯示器安裝在位于同一機柜或距離3500系統100英尺的面板開孔中。(當使用外部電源時，距離3500系統最多4000英尺)。
4. 獨立安裝-顯示器安裝在墻壁或面板上，位于距離3500系統100英尺遠的地方。(當使用外部電源時，距離3500系統最多4000英尺)。

每個3500機架最多可連接兩個顯示器，每個顯示器需要一個空的3500機架槽位來插入相應的DIM。當顯示器不是正面安裝時，DIM和顯示器之間的電纜連接可以從3500機架的前部或從機架后部的I/O模塊連接。
需要超過100英尺電纜的應用必須使用外部電源和電纜適配器。使用背光顯示單元的應用必須使用外部電源。有兩個外部電源:一個用于連接到115 Vac和另一個用于連接到230 Vac。
外部電源/端子排安裝套件簡化了外部電源的安裝。外部電源/端子條安裝套件的設計適合于獨立安裝外殼。該套件簡化了外部電源在獨立安裝外殼或用戶提供的外殼中的安裝。

The 3500/93 System Display is designed to meet the requirements of American Petroleum Institute (API) Standard 670 and provide local or remote visual indication of all 3500 Machinery Protection System information residing in the rack including:
? System Event List
? Alarm Event Lists
? All Channel, Monitor, Relay Module, Keyphasor* Module or Tachometer Module data
The 3500/93 System Display is configured using 3500 Rack Configuration Software. The display can be mounted in any of four ways:
1. Face Mounting – display installs directly over the front panel of any full size 3500 rack using a special hinged support. This permits access to the rack’s buffered output connectors and user-interface buttons and switches without disconnecting or disabling the display.
Note: For this mounting option only, the Display Interface Module (DIM) must be installed in slot 15 (right-most slot) of the rack. The Face Mounting option is not compatible with the 3500 Mini-rack.
2. 19-inch EIA Rack Mounting – display is mounted on 19-inch EIA rails and located up to 100 feet away from the 3500 System. (Up to 4000 feet away from the 3500 System when using the External Power Supply).
3. Panel Mounting – display is mounted in a panel cutout located in the same cabinet or up to 100 feet away from the 3500 System. (Up to 4000 feet away from the 3500 System when using the External Power Supply).
4. Independent Mounting – display is mounted flush against a wall or panel and located up to 100 feet away from the 3500 System. (Up to 4000 feet away from the 3500 System when using the External Power Supply).

Up to two displays can be connected to each 3500 rack and each display requires one empty 3500 rack slot for insertion of its corresponding DIM. When the display is not face-mounted, the cable connection between the DIM and the Display can be made from the front of the 3500 rack or from the I/O module at the rear of the rack.
Applications that require a cable longer than 100 feet must use the External Power Supply and Cable Adapter. Applications that use the back lighted Display Unit must use the External Power Supply. There are two External Power Supplies: one for connection to 115 Vac and the other for connection to 230 Vac.
The External Power/Terminal Strip Mounting Kit eases installation of External Power Supplies. The External Power/Terminal Strip Mounting Kit is designed to fit in the Independent Mount Housing. The Kit streamlines installation of an External Power Supply in both the Independent Mount Housing or a user supplied housing.